Saturday 5 October 2013

Forks

Man i'm slow at updating this!

With the rear of the bike coming together I focused on the forks, mainly because the weight at the rear was tippling the bike off it's stand!

I decided to fit the R1 forks before i'd decided on the project, i love the look of them!!
Luckily the steerer tube is within 5mm of the stock R65 one, only problem i came across is the R1 steerer tube is 2mm bigger than the R65.
I purchased new R65 bearings and spent a little while, and a fair few carbide tips, turning the bearing to what i needed.

Biggest problem i had was removing the old bearing races, after trying everything i could think of, all forms of lube, hammers and dremel attachments, i resigned and gave up.
Whilst slupmed in misery of my defeat i called a mate to whine at him, when he'd been informed he told me of a trick they used to do when he was racing.....

'Run a rim of weld around the stuck race and the heat of the welding will contract it enough to remove it'

It blooming did too!!





Ta Da!!!!

I whipped the forks in and pratted about on the lathe making a few spacers to centre the wheel
Think it's gone in nicely centred.




Tuesday 6 August 2013

Subframe

Started mocking up the subframe for the bike, not quite sure if it'll work as it's the first i've built, if its not right i'll get one made after.

I used 10mm box section stainless tube






It seems a little long as it is, but i've left some room to trim it down if required.


 I'll be looking to run it on this angle


Tom (Chief) at Holme Valley Customs - www.holmevalleycustoms.com/ - sent a package of pre cut frame tabs, saved me some time trying to get them cut.
I've tacked on the two shock mounts to the mid section of the front cross bar.

Need to make the support arms to the frame but i'm happy with it so far






dry run

With the swingarm mounts tacked in place i couldn't resist putting the pieces togther!


Happy with the way it looks, fingers crossed the propshaft will fit!



Love the rear view, for me the rear wheel balances the bike from the back instead of a 4.0 tyre.




Sunday 4 August 2013

Frame fix

So with the frame cut and me coming to realise no amount of gussets will do this right i had to turn to Tom for advice, and he loved it that he was right.

Thankfully his gloating only lasted a few minutes and he quickly came up with a perfect solution.






Tom decided rather than do my suggestion of plates and gussets, we'd be better to widen the hole to take a piece of tube the right diameter for the swingarm to move in and a decent width to step out the mount.
We turned the original mount in the lathe to remove any square edges/ pieces of metal, cut a 10cm disc to seat the mount, welded them together and welded that to the tube tacked in the frame (i haven't got any photos of this process)

Tom it all welded together


We removed some of the tube facing the swingarm, allowing the swingarm to come over far enough centering the rear wheel.



 And its in!!
I'll be putting a gusset on it to make sure it's strong enough





Saturday 27 July 2013

Logo

Thanks to TC Customs for the design of the superbeemer logo!!

and i couldn't resist making a few t-shirts with it on!!!

All the best

Chopped

Well, seen as I was this far into it with all the parts for the project bought i figured what the.......
Plus i couldn't be beaten by it, though the thought had gone through my head.


Armed with a trusty angle grinder i set about the right swingarm mount.
It wasn't quite like that, i'd been warned to brace the crossbars so the frame didn't flex open once id cut the mount out.






A 12mm threaded bar and 4 nylock nuts did the job perfect, crude yes, but it worked a treat.
The bevel on the top of the nut located the bar perfectly central in the threads of the mount.
Once i'd checked it a fair few times it was time to chop, it's funny how eager i was to do it, seen as though i'd no idea what i'd do to reposition it in the right place and connect it to the frame.

And it's out.......sorry for the crappy iphone pic.





Now to figure out how to re-attach it!!




Monday 1 July 2013

Chop and see!

Well i have a little problem.
The casting on the swingarm is double the size of the R65 one.
This has pushed the rear wheel centre 20mm to the left, not quite the easy project i was hoping for!
Whilst looking at the frame to figure out what to do i forgot to take any photos of it with the wheel on and nowhere near centre!!

The lines in the pic are the outside edges of the rim, the left is 40mm from the frame mounting, the right 80 mm off!

The other problem it posed was the prop has to run on a 2cm angle, and there isn't alot of clearance for one in the casting on that kind of an angle!!






This got me anxious, but i'm sure it'll be reet!!
I marked the frame to show how far over the rear diff UJ will be, it's not a massive angle over the 25cms but the inner casting is close for the more modern propshaft.
The line on the left is the original UJ mark, the right is where the new one will line up.

Thansk